highly stable, light-curing base plates for prosthetics
The innovative chemical composition of the primobase base plates significantly reduces the
Materials usual stickiness. At the same time they could
Processing properties, as well as the accuracy of fit
be noticeably improved.
primobase - light-curing base plate 1,2mm
plus statutory VAT and shipping costs
69,95 €
light curing
baseplates
only 1.2 mm thick and extremely precise
-
primobasesame strength as conventional double the thickness impression tray materials -
primobaseonly 1.2mm thick, so hardly any need to adjust and/or shorten denture teeth to match the given vertical dimension during the set-up -
primobaseextremely precise – to an extent that the base plate with the set-up teeth “adheres” to the palate during the try-in (suction effect) -
primobasedoes not require a second curing cycle off the model upside down -
primobasecures in most conventional light curing units (do not use strobe lights!)
-
primobasesame strength as conventional double the thickness impression tray materials
-
primobaseonly 1.2mm thick, so hardly any need to adjust and/or shorten denture teeth to match the given vertical dimension during the set-up
-
primobaseextremely precise – to an extent that the base plate with the set-up teeth “adheres” to the palate during the try-in (suction effect)
-
primobasedoes not require a second curing cycle off the model upside down
-
primobasecures in most conventional light curing units (do not use strobe lights!)
uses
- Base plates for bite registration
- lineup
- Try-in of full and partial dentures
advantages
- particularly low plate thickness of only 1.2mm. As a result, the prosthetic teeth generally do not have to be shortened from the basal side, even if there is unfavorable space
- Despite its low thickness, it has a high level of stability comparable to much thicker spoon plates
- Extremely precise – due to the exact fit, the set-up "sucks" in the patient's mouth during the try-in
- Best polymerisation properties – no second light-curing cycle required without a model
- can be polymerized in all common light curing devices (if possible, do NOT use strobe devices)
product pictures
- Base plates for bite registration
- lineup
- Try-in of full and partial dentures
- particularly low plate thickness of only 1.2mm. As a result, the prosthetic teeth generally do not have to be shortened from the basal side, even if there is unfavorable space
- Despite its low thickness, it has a high level of stability comparable to much thicker spoon plates
- Extremely precise – due to the exact fit, the set-up "sucks" in the patient's mouth during the try-in
- Best polymerisation properties – no second light-curing cycle required without a model
- can be polymerized in all common light curing devices (if possible, do NOT use strobe devices)
technical tipsuseful tips for your workflow
- Wet the fingertips with a small amount of Metatouch IM 200 Finger and Instrument Isolation to smooth the primobase surface after adapting.
- The most perfect fit is achieved by using the Metavac deep-drawing process, because with this process the primobase plate is pressed against the model with a defined pressure throughout the entire light-curing process.
working procedurethe workflows for standard applications
working procedure:
- Apply separator to the model (preferably Metatouch IM200)
- Adapt the base plate to the model with your fingers and/or instrument
- For an even more precise fit use the Metavac suction device (TZ-KIT). This will ensure maximum precision
- Cure for 6 minutes – no second curing cycle off the model needed
- Remove base plate and finish it
- Wet the fingertips with a small amount of Metatouch IM 200 Finger and Instrument Isolation to smooth the primobase surface after adapting.
- The most perfect fit is achieved by using the Metavac deep-drawing process, because with this process the primobase plate is pressed against the model with a defined pressure throughout the entire light-curing process.
working procedure:
- Apply separator to the model (preferably Metatouch IM200)
- Adapt the base plate to the model with your fingers and/or instrument
- For an even more precise fit use the Metavac suction device (TZ-KIT). This will ensure maximum precision
- Cure for 6 minutes – no second curing cycle off the model needed
- Remove base plate and finish it
light curing
baseplates
baseplates
primobase - light-curing base plate 1,2mm
plus statutory VAT and shipping costs
69,95 €